Short answer: A slab-on-grade contractor pours a concrete slab directly on prepared ground rather than over a basement or crawl space. The contractor prepares and compacts the subgrade and base, adds any vapor retarder, insulation and reinforcement the plans call for, sets forms and edges, places and finishes the concrete, cuts control joints, and cures the slab. In Michigan, the main things to get right are frost protection at the edges, drainage, and a well-compacted base over clay soil. Your local building department sets the code requirements.
Slab-on-grade construction is used for garages, pole barns, shops, additions, sheds, patios, and many commercial buildings around Ypsilanti, Ann Arbor, Saline, Dexter, Belleville and the rest of southeast Michigan. This guide explains how it’s built, what affects quality, and how to compare contractors.
What “slab on grade” means
“Grade” is the ground level. A slab-on-grade (also called slab-on-ground) is a concrete floor supported directly by the soil and base under it. A structural slab spans between supports instead. Because the ground carries the load, the slab can only be as good as the ground under it.
The American Concrete Institute (ACI) publishes guides on designing and building slabs-on-ground and concrete floors (see concrete.org). Those documents cover subgrade support, joint spacing, reinforcement and curing.
How a slab-on-grade is built
- Site review and layout. Check the plans, drainage, access, utilities and setbacks. In Michigan, always contact MISS DIG 811 before digging (missdig811.org).
- Excavation and subgrade prep. Remove topsoil and organic material. Soft or wet spots are dug out and replaced, not covered over.
- Base course. Place compacted granular base in lifts. A uniform, compacted base is what prevents settlement cracks later. Our post on why a concrete contractor prioritizes site preparation explains why.
- Frost protection. Buildings need footings or frost-protected edges that meet the local code. Requirements differ between a heated building, an unheated garage or pole barn, and a patio. Your city or township building department, under the Michigan Residential or Building Code, decides what applies.
- Vapor retarder and insulation where the plans call for them, especially under heated floors and finished spaces.
- Reinforcement (wire, rebar or fibers) as specified. Reinforcement controls crack width. It doesn’t replace a good base.
- Forms, pour and finish. Exterior slabs exposed to freeze-thaw and salt should use air-entrained concrete. Interior floors are finished to suit their use.
- Control joints. Saw-cut or tooled on time so the slab cracks along the joints, not across panels.
- Curing. Keep the slab moist and protected from freezing while it gains strength. The Portland Cement Association (cement.org) has guidance on curing and cold-weather concreting.
Michigan conditions that change the design
- Frost and freeze-thaw. Southeast Michigan winters freeze water in the soil and in the concrete’s pores. Frost protection and air entrainment are the defenses.
- Clay soils. Much of Washtenaw and Wayne counties has clay that holds water and moves with moisture. Drainage and a proper base matter more here than on sandy sites.
- Road salt. Garage and commercial slabs see salt brine dripping off vehicles. Mix design, finishing and sealing all affect how well the surface holds up.
- Short pour season. Exterior slabs are mostly poured from spring through fall. Winter pours need heat, blankets and planning.
Common slab-on-grade projects
- Garage floors and new garages. See garage floors.
- Pole barn floors. See pole barns, which are popular around Dexter, Milan and Whitmore Lake.
- Additions, sheds and shop floors. See concrete slab installation and repair.
- Commercial pads and lots. See commercial lots and parking lots.
- Patios. See concrete patios.
How to choose a slab-on-grade contractor
Ask every bidder the same questions and compare the answers, not just the totals:
- Who pulls the permit, and who schedules inspections?
- What base material and thickness will you use, and how will you compact it?
- What slab thickness and reinforcement are you proposing, and why?
- Is the mix air-entrained? (Exterior and garage slabs.)
- Where will the control joints go, and when will you cut them?
- How will you handle drainage and slope?
- How will you cure and protect the slab, especially in cold weather?
- Is the bid written and itemized? See why a written estimate matters.
- Are you licensed and insured in Michigan? You can verify builder licenses through the State of Michigan’s LARA license lookup.
A bid that can’t answer these clearly usually means the contractor is pouring on whatever ground is there.
Repairing an existing slab-on-grade
Cracked, sunken or heaved slabs usually point to a base, drainage or frost problem. Small stable cracks can be filled. Settled sections can sometimes be cut out and re-poured over a rebuilt base. Widespread failure means replacing the slab. Read concrete resurfacing vs replacement or see our concrete repair service.
Working with GB Cement
GB Cement (GatlinByrd Cement) is a concrete contractor based in Ypsilanti. We pour slabs, garage floors, pole barn floors and commercial pads in Ypsilanti, Ann Arbor, Saline, Belleville, Dexter and nearby towns. Send your plans or a few photos and the address through the contact page, or call (734) 323-8882.
FAQ
What is a slab-on-grade foundation?
It’s a concrete slab supported directly by prepared ground, with no basement or crawl space under it. It’s often thickened or footed at the edges for frost protection.
Is slab-on-grade OK in Michigan’s climate?
Yes, if frost protection, drainage, base compaction and the concrete mix are designed for local conditions and meet your local building code.
How thick should a slab-on-grade be?
It depends on the load and use (a patio, a garage, a shop with equipment). The plans or local code set the minimum. A contractor should explain the thickness they propose.
Do I need a permit for a concrete slab?
Often, yes, especially for a garage, an addition or a pole barn. Ask your city or township building department, or ask us when we visit the site.
Why do slabs crack?
Concrete shrinks as it cures, and the ground moves. Control joints, a good base and proper curing keep cracks along the joints and keep them narrow.